|
|
Главная » 2008 » Август » 15 » SpeedFan 4.34 Final
00:03 SpeedFan 4.34 Final |
SpeedFan
- бесплатная программа, которая следит за температурой, скоростью
движения кулера и напряжением. SpeedFan также может отображать
температуру жесткого диска, если устройство поддерживает эту опцию.
Однако, главной функцией SpeedFan является наблюдение за скоростью
вращения кулера и ее изменение в зависимости от температуры внутри
компьютера. Это помогает уменьшить шум и потребление электроэнергии.
SpeedFan
monitors fan speeds, temperatures and voltages in computers with
hardware monitor chips. It can even access S.M.A.R.T. info for those
hard disks that support this feature and show hard disk temperatures
too, if supported. It can even change the FSB on some hardware. At the
lowest level, it is a hardware monitor software, but its main feature
is that it can control fan speeds according to the temperatures inside
your pc, thus reducing noise and power consumption.
Version 4.34:
-added full support for SiS964 SMBus
-added full support for SiS966 SMBus
-added full support for ULi M1575 SMBus
-added full support for VIA VT8237S SMBus
-added full support for VIA VT8251 SMBus
-added full support for nVidia MCP61 SMBus
-added full support to read internal temperatures on AMD K10 processors
-added native nVidia video card (up to, but excluding 8xxx) internal temperature reporting
-added full support for SMSC SCH5307
-added full support for F8000 temperatures and fan speeds
-added full support for SMSC EMCT03
-added full support for WINBOND W83793G, including ADVANCED options
-added support for Fintek F71782F hardware monitor at unusual addresses
-added support for Winbond W83627DHG at unusual addresses
-added support for ITE IT8726F hardware monitor at unusual addresses
-added support for a new stepping of the Andigilog aSC7621
-Winbond W83791D properly handles higher fan divisors for fan1, fan2 and fan3 and shows fan4 and fan5 too
-added SMSC LPC47M192 FAN DIVISOR settings in CONFIGURE / ADVANCED
-added full PWM support to SMSC LPC47B397, including settings in CONFIGURE / ADVANCED
-CONFIGURE
now allows to go as low as -60C when selecting the DESIRED and WARNING
levels to let users of the RELATIVE Intel Core temperature reading
properly configure SpeedFan
-improved DDR2 memory module size detection
-added preliminary DDR3 identification
-new icon by Bengt Strom
-fixed an issue where Intel Core temperatures on multi core systems reported the same temperature for all cores
-improved
Tjunction detection for Intel CORE temperatures (you might no longer
need the temperature offset in CONFIGURE / ADVANCED)
-fixed crash on several DFI motherboards
-fixed the detection of older revisions of the ITE IT8705F
-restored the correct clock speed after resume from hibernation
-rewritten
the logic of the usage of a synchronizer in the thread that reads CPU
usage (this will fix the SpeedFan not exiting issue)
-address $2E on
DFI motherboards is no longer scanned if the motherboard model starts
with LP. If you have one of these models and you know that there should
be a valid chip at that address, send me a SEND REPORT (INFO tab) with
some NOTES
-fixed ADT7475 temperature readings when in offset 64 mode
-fixed a bug when changing the type of data to be charted
-mails sent by SpeedFan now properly separate headers and the body with a blank line
-fixed an issue with SUN 2864 motherboard
Размер: 1,60 МБ
No pass.
|
|
Просмотров: 811 |
Добавил: Admin
| Рейтинг: 0.0/0 |
|
|
|
